over
    Software
    Download
  Stations    Sensors     Software     Communication    Installation    Support   Contact Us 
firmware Support Download

Our Firmware is downloadable at no charge, but requires use of our Vantage Pro Updater for Vantage Pro2 or Vantage Pro Updater for Original Vantage Pro, which are available for purchase through our secure e-commerce system.

If your Vantage Pro2 Console Firmware is dated 28-Nov-05 or later, you may update your console with the Direct PC Install file. This is a stand alone application that will update your console firmware directly through the WeatherLink data logger connected to your PC. (WeatherLink for Vantage Pro2 (#6510SER, 6510USB, 6540, 6544, 6550 or 6560) is required to use the Direct PC Install file.) DO NOT USE the Direct to PC Install file if your Vantage Pro2 firmware revision is dated before November 28, 2005.

WeatherLink for Mac OSX (#6520) does not support Direct PC Install files. To update your console, use a Vantage Pro2 Updater.

Vantage Vue

Vantage Vue Console Firmware, Direct PC Install

Download (467 KB)

NOTE: This firmware is only for Vantage Vue Consoles (#6351, 6351M, 6351UK or #6312EU).

Firmware version 2.12

  1. Fixed display of historical yearly rain totals over 812 mm for 0.2 mm rain collectors (high, lows, and graphs).
  2. Range of LCD contrast adjustment reduced by half.
  3. Now you must be in the Current Weather Screen to move to the Receive Diagnostic screen.

 

WEATHERLINK

   06/08/2010: WeatherLinkIP Datalogger Firmware, 1.0.9

    WeatherLinkIP Datalogger Firmware, 1.0.9
     Download Now (344 KB)

    Version 1.0.9

  1. Fixed problem with the DNS query that may prevent it from uploading data to the server
  2. Fixed problem with uploading archive pages to the server

    Version 1.0.8

  1. Fixed a bug that caused the data logger to stop uploading data periodically. This halt in uploading was caused by a PING message sent by some routers.
  2. Changed data upload format to reduce upload bandwidth to the server and fix missing high/low data.
  3. Added support for 2 DNS servers in dynamic IP address mode. If the data logger cannot successfully resolve the WL.com name through the two given DNS servers it will try with the Google public DNS at address 8.8.8.8.
  4. Config page always displays the 1st DNS server even if it is using the Google public DNS server.

VANTAGE PRO2

   1/13/2009: Vantage Pro2 Cable Console Firmware, Direct PC Install

    Vantage Pro2 Cabled Console Firmware, Direct PC Install
    Download Now (648 KB)

    NOTE: This firmware is only for Vantage Pro2 Cabled Consoles (#6312C).

    Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed clearing of yearly ET history data.
  3. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82
  4. Fixed a bug that when changing units in software caused the console to not reflect the change immediately.
  5. Fixed graph so that zooming to a different span always starts at the first point.
  6. Fixed display of historical yearly rain totals over 813 mm for .2 mm rain collectors (highs, lows and graphs).
  7. You can now only get to the Receive Diagnostics Screen from the Current Screen.
  8. Cabled console will now gracefully handle a serial command terminated with two of \n or \r characters.

   2/18/2010: Vantage Pro2 Wireless Console Firmware, Direct PC Install, 1.90  

    Vantage Pro2 Wireless Console Firmware, Direct PC Install
     Download(656 KB)

    NOTE: This firmware is only for Vantage Pro2 Wireless Consoles (Davis #6312 or Davis #6312OV).   

    Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed clearing of yearly ET history data.
  3. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82.
  4. Fixed a bug that when changing units in software caused the console to not reflect the change immediately.
  5. Fixed graph so that zooming to a different span always starts at the first point.
  6. Fixed display of historical yearly rain totals over 813 mm for 0.2 mm rain collectors (highs, lows and graphs).
  7. You can now only get to the Receive Diagnostics Screen from the Current Screen.

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data     containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.
    Firmware version 1.80 1. Improved wind speed translation algorithm for increased accuracy. 2. Improved     digital barometer measurements at very high temperatures.

    1/13/2009: Weather Envoy Cabled Firmware, Direct PC Install
    Download (694KB)

    NOTE: This firmware is only for a Vantage Pro2 Cabled Weather Envoy (#6316C).

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data     containing a 10 (x0A) or a 13 (x0D).
    Note: This issue only affects third-party software developers.
    Firmware version 1.80
    1. Improved wind speed translation algorithm for increased accuracy.
    2. Improved digital barometer measurements at very high temperatures.
    Firmware version 1.75a
    1. Fixed a compiler bug that would not allow firmware update v1.75 to work properly.
    Firmware version 1.75
    1. Fixed a bug that causes the console to display incorrect yearly rain values when the unit of measure for     rain is set to millimeters.
    2. Supports direct updates using USB or TCP/IP connections.

    1/13/2009: Weather Envoy Wireless Firmware, Direct PC Install
    Download (605KB)

    NOTE: This firmware is only for a Vantage Pro2 Wireless Weather Envoy (#6316 or #6316OV).

    Firmware version 1.90

   1.CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15    minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use    this feature.
   2.Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data     containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.
    Firmware version 1.80
    1. Improved wind speed translation algorithm for increased accuracy.
    2. Improved digital barometer measurements at very high temperatures.
    Firmware version 1.75a
    1. Fixed a compiler bug that would not allow firmware update v1.75 to work properly.
    Firmware version 1.75
    1. Fixed a bug that causes the console to display incorrect yearly rain values when the unit of measure for     rain is set to millimeters.
    2. Supports direct updates using USB or TCP/IP connections.

    1/13/2009: Vantage Pro2 Cabled Console Firmware
    Download (471KB)

    NOTE: This firmware is only for Vantage Pro2 Cabled Consoles (#6312C).

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data
    containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.
    Firmware version 1.80
    1. Improved wind speed translation algorithm for increased accuracy.
    2. Improved digital barometer measurements at very high temperatures.
    Firmware version 1.75
    1. Fixed a bug that causes the console to display incorrect yearly rain values when the unit of measure for     rain is set to millimeters.
    2. Supports direct updates using USB or TCP/IP connections.

    Vantage Pro2 Wireless Console Firmware
    Download (548KB)

    NOTE: This firmware is only for Vantage Pro2 Wireless Consoles (#6312 or #6312OV) and is intended for
    update using a Vantage Pro2 Updater.

    Firmware version 1.90

  1. CWOP uploads will now contain 2 min average wind speed, 10 min wind gust and direction of gust, last 15 minutes of rain, last 1 hour of rain and Altimeter. Must also have WeatherLink software v5.9.0 or later to use this feature.
  2. Fixed clearing of yearly ET history data.
  3. Fixed a bug that caused the barometer value to have a large error after updating to firmware version 1.82
  4. Fixed a bug that when changing units in software caused the console to not reflect the change immediately.
  5. Fixed graph so that zooming to a different span always starts at the first point.
  6. Fixed display of historical yearly rain totals over 813 mm for .2 mm rain collectors (highs, lows and graphs).
  7. You can now only get to the Receive Diagnostics Screen from the Current Screen.

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data             containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.

    Weather Envoy Cabled Firmware
    Download (470KB)

    Note: This firmware is only for a Vantage Pro2 Cabled Weather Envoy (#6316C).

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data     
    containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.
    Firmware version 1.80
    1. Improved wind speed translation algorithm for increased accuracy.
    2. Improved digital barometer measurements at very high temperatures.
    Firmware version 1.75
    1. Fixed a bug that causes the console to display incorrect yearly rain values when the unit of measure for     rain is set to millimeters.
    2. Supports direct updates using USB or TCP/IP connections.

    Required: To use these files you will need a Davis Weather Envoy (#6316C) and a Davis Vantage Pro2 Firmware     Updater (#6311VP2).

    Weather Envoy Wireless Firmware
    Download (469 KB)

    NOTE: This firmware is only for a Vantage Pro2 Wireless Weather Envoy (#6316 or #6316OV).

    Firmware version 1.82
    1. Changed “ALL CLEAR” function so that it does not clear any user-set calibration numbers.
    2. Further improved wind speed translation algorithm for increased accuracy.
    3. Improved data logging of high wind speed measurements in environments that get poor reception.
    4. Fixed a communication problem where the console output an extra “\n\r” if it received binary data
    containing a 10 (x0A) or a 13 (x0D). Note: This issue only affects third-party software developers.
    Firmware version 1.80
    1. Improved wind speed translation algorithm for increased accuracy.
    2. Improved digital barometer measurements at very high temperatures.
    Firmware version 1.75
    1. Fixed a bug that causes the console to display incorrect yearly rain values when the unit of measure for     rain is set to millimeters.
    Required: To use these files you will need a Davis Weather Envoy (#6316 or #6316OV) and a Davis Vantage     
    Pro2 Firmware Updater (#6311VP2).
 HOME ABOUT US SITEMAP LINK PARTNERS